CONTINENTAL VALVE COVER GASKET- FITS E-185 & more Part# RG-532451 SiliconeClick here to purchase or contact the seller of this item on eBay |
|
|
| Current Price: 11.50 USD |
VALVE COVER GASKETS - SILICONE
for
CONTINENTAL ENGINES - see list below
- Our silicone rubber gaskets are made from aerospace mechanical
grade AMS silicone and designed to withstand temperatures
up to 400 degrees Fahrenheit.
- Therefore, they will not break down and deform or crack up
like cork or
neoprene.
- Our gaskets seal uneven and warped surfaces
and eliminates corrosion.
-
Gaskets are 100% reusable.
FAA-PMA APPROVED FOR THE FOLLOWING ENGINES
Fits Models: Continental
E-165-2;
E-185-1,-3, -8, -9, -11;
E-225-4, -8;
O-470-A, -E, -J;
IO-470-J, -K;
TSIO-520-AE Series;
LTSIO-520-AE Series
PART #: RG-532451
OEM # 532451
SUPERSEDED OEM NUMBERS:
655703, 653193, 649973, 646234, 532451
Gaskets have seven bolt holes and are 1/8" thick silicone.
Gaskets are priced per gasket.
Reusable.
INSTALLATION AND MAINTENANCE PROCEDURES:
THE GASKET SURFACES MUST BE CLEAN AND DRY.
1. Remove the valve cover and gasket in accordance with the Continental procedure
or in accordance with an acceptable procedure used by the shop performing
the installation.
2. Clean the valve cover and the cylinder surfaces of all residual material.
3. Install gaskets, DRY,
4. Replace the valve cover and torque the cover bolts to 25 in-lbs.
"CAUTION" - DO NOT OVER TIGHTEN."
Over tightening causes the gasket to bulge of squeeze out.
If that happens then back off on the torque.
5. Check the cover bolt torque after an engine run up to take off power or first flight
and re-torque the bolts to 20 in-lbs.
6. Check the cover bolt torque annually, and re-torque to 20 in-lbs, if necessary.
The gaskets are re-usable and the service life of the gasket is determined by its
physical condition on removal.
If the gasket is still pliable and without cracks, tears, or deterioration, it may
be re-used, otherwise discard.
TO REUSE GASKETS:
- Wash gaskets briefly in hot soapy water.
- Rinse well and dry all surfaces.
- Re-install using the above installation instructions.
Save instructions for future reference.
Instructions do come with the gaskets.
PROUDLY MADE IN THE USA.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
USE CORK? GET REAL! REAL Gaskets that is…
REAL Gaskets Tennessee is a manufacturer of silicone rubber gaskets
for aircraft, automobile, and motorcycle engines.
Our silicone rubber gaskets are made from aerospace mechanical
grade AMS silicone, designed to withstand temperatures
up to 400 degrees Fahrenheit and to last the life of the engine.
Our gaskets seal uneven surfaces, eliminate corrosion and
are 100% reusable.
We manufacture valve cover gaskets for:
Aircraft: Continental, Franklin, Lycoming, Pratt & Whitney and
Wright radial piston aircraft engines.
Automobiles: Chevrolet, Ford, GM, Mopar, Porsche and VW
automobile engines.
Featuring NEW *ULTIMATE* GASKETS that are fiberglass
reinforced silicone. Check them out!
Motorcycles: BMW, Harley-Davidson, Suzuki, BSA, Ducati,
Moto Guzzi, Norton, Triumph, Saab and most other
motorcycle engines.
If you are tired of oil leaks, then a silicone rubber gasket is the
only way to go, and REAL Gaskets Tennessee is the only
place you can get “The Original” silicone rubber gasket.
MADE IN THE USA.
|
|
Click here to purchase or contact the seller of this item on eBay