CONTINENTAL VALVE COVER GASKET- Silicone; FITS IO-346,O-470,IO-520 # RG-534857


Click here to purchase or contact the seller of this item on eBay

Current Price: 12.50 USD

 

VALVE COVER GASKETS - SILICONE

for

 CONTINENTAL ENGINES - see list below 


 -   Our silicone rubber gaskets are made from aerospace mechanical 

       grade AMS silicone and designed to withstand temperatures 

       up to 400 degrees Fahrenheit.   

-   Therefore, they will not break down and deform or crack up 

      like cork or neoprene.   

-   Our gaskets seal uneven and warped surfaces,  and

     eliminates corrosion.

-   Gaskets are 100% reusable.


FAA-PMA approved for the following 

CONTINENTAL ENGINE MODELS: 


IO-346;  

IO-370; 

O-470-B,-G,-GCI,-K,-L,-M,-P,-R,-S,-U; 

IO-470-D,-E,-F,-G,-H,-K,-L,-M,-N,-P,-R,-S,-U,-V,-VO; 

IO-520-A,-B,-BA,-BB,-C,-CB,-D,-E,-F,-J,-K,-L,-M,-MB; 


TSIO-520-AF,-B,-BB,-C,-CE,-D,-DB,-E,-EB,-G,-H,-J,-JB,-K,-KB,

-L,-LB,-M, -N,-NB,-P,-R,-T,-U,-UB,-VB,-WB Series; 


IO-550-A,-B,-C,-D,-E,-F,-L; 

TSIOL-550-A,-B,-C


PART #:   RG-534857

OEM # 534857

SUPERSEDED OEM NUMBERS: 655528, 653191, 649970, 534857

Gaskets have eight (8) bolt holes and are 1/8" thick silicone.

Price per gasket.

Reusable.


INSTALLATION AND MAINTENANCE PROCEDURES:

THE GASKET SURFACES MUST BE CLEAN AND DRY.     

      1.   Remove the valve cover and gasket in accordance with the 

            Continental procedure or in accordance with an acceptable 

            procedure used by the shop performing the installation.

2.   Clean the valve cover and the cylinder surfaces of all residual material.


3.   Install gaskets, DRY.


4.   Replace the valve cover and torque the cover bolts to 25 in-lbs  


       "CAUTION"  - DO NOT OVER TIGHTEN." *


5.   Check the cover bolt torque after an engine run up to take off power or first flight


 and re-torque the bolts to 20 in-lbs.


6.   Check the cover bolt torque annually, and re-torque to 20 in-lbs, if necessary.

       

        The gaskets are re-usable and the service life of the gasket is 

        determined  by its physical condition on removal.  

  

        If the gasket is still pliable and without cracks, tears, or 

       deterioration, it may be re-used, otherwise discard.


*   Over tightening causes the gasket to bulge of squeeze out.   

     If that happens then back off on the torque.


 

TO REUSE GASKETS:

  1.  Wash gaskets briefly in hot soapy water.  
  2.  Rinse well and dry all surfaces. 
  3.  Re-install using the above installation instructions.


Save instructions for future reference. 

Instructions do come with the gaskets.


PROUDLY MADE IN THE USA.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 


USE CORK?      GET REAL!      REAL Gaskets that is…

REAL Gaskets Tennessee is a manufacturer of silicone rubber gaskets 

for aircraft, automobile, and motorcycle engines.


Our silicone rubber gaskets are made from aerospace mechanical 

grade AMS silicone, designed to withstand temperatures up 

to 400 degrees Fahrenheit and to last the life of the engine.


Our gaskets seal uneven surfaces, eliminate corrosion and 

are 100% reusable.


We manufacture valve cover gaskets for:


Aircraft: Continental, Franklin, Lycoming, Pratt & Whitney and 

Wright radial piston aircraft engines.


Automobiles: Chevrolet, Ford, GM, Mopar, Porsche and 

VW automobile engines.  

Featuring NEW *ULTIMATE* GASKETS 

that are fiberglass reinforced silicone and extra tough.   

Check them out!


Motorcycles:  BMW, Harley-Davidson, Suzuki, BSA, Ducati, 

Moto Guzzi, Norton, Triumph, Saab and most other 

motorcycle engines. 


If you are tired of oil leaks, then a silicone rubber gasket is 

the only way to go, and REAL Gaskets Tennessee is the 

only place you can get “The Original” silicone 

rubber gasket.


MADE IN THE USA.


CONTINENTAL VALVE COVER GASKET- Silicone;  FITS IO-346,O-470,IO-520 # RG-534857


Click here to purchase or contact the seller of this item on eBay