CONTINENTAL Valve Cover Gasket - FITS C-85, O-200 & more- # RG-530162 Silicone


Click here to purchase or contact the seller of this item on eBay

Current Price: 10.00 USD

 

VALVE COVER GASKETS -  SILICONE 

for

CONTINENTAL Engines 

A-65; A-75; C-75; C-85; C-90; C-125, C145,

O-200;   IOL-200; O-300; GO-300; IOL-300

Specific engines listed below.


   -   Our silicone rubber gaskets are made from aerospace 

        mechanical grade AMS silicone and designed to 

        withstand temperatures up to 400 degrees Fahrenheit.   

   -   Therefore, they will not break down and deform or crack up 

        like cork or neoprene.   

   -   Our gaskets seal uneven and warped surfaces, plus

       eliminates corrosion.

   -   Gaskets are 100% reusable.


FAA-PMA approved FOR 

CONTINENTAL ENGINE MODELS:                          


A-65; A-75; 

C-75; C-85; C-90;

C-125-2; 

C-145-2, -2H;

O-200;   IOL-200;

O-300-A,-B,-C,-D;

GO-300-A,-B,-C,-D,-E;

IOL-300


PART #:   RG-530162

OEM # 530162

SUPERSEDED OEM NUMBERS: 655706, 653728, 653192, 649985, 530162, 3500

Gaskets have six bolt holes and are 1/8" thick silicone.

Price is per gasket.

Reusable.


INSTALLATION AND MAINTENANCE PROCEDURES:

THE GASKET SURFACES MUST BE CLEAN AND DRY.  

      1.   Remove the valve cover and gasket in accordance with the 

            Continental procedure or in accordance with an acceptable 

            procedure used by the shop performing the installation.

2.    Clean the valve cover and the cylinder surfaces of all residual 


       material.


3.    Install gaskets, DRY.


4.    Replace the valve cover and torque the cover bolts to 25 in-lbs.   

 

       "CAUTION" -  DO NOT OVER TIGHTEN.


       Over tightening makes the gasket bulge of squeeze out.


5.    Check the cover bolt torque after an engine run up to take off power or 

       first flight  and re-torque the bolts to 20 in-lbs.


6.    Check the cover bolt torque annually, and re-torque to 20 in-lbs, if necessary.

       

        The gaskets are re-usable and the service life of the gasket is 

        determined by its physical condition on removal.    

        If the gasket is still pliable and without cracks, tears, 

        or deterioration, it may be re-used, otherwise discard.


   

 

TO REUSE GASKETS:

  1.   Wash briefly in hot soapy water.  
  2.   Rinse well and dry all surfaces. 
  3.   Re-install using the above installation instructions.


Save instructions for future reference. 

Instructions do come with the gaskets.


PROUDLY MADE IN THE USA.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~


USE CORK?      GET REAL!      REAL Gaskets that is…

REAL Gaskets Tennessee is a manufacturer of silicone rubber gaskets 

for aircraft, automobile, and motorcycle engines.



Our silicone rubber gaskets are made from aerospace mechanical 

grade AMS silicone, designed to withstand temperatures 

up to 400 degrees Fahrenheit and to last the life of the engine.


Our gaskets seal uneven surfaces, eliminate corrosion and 

are 100% reusable.

  

We manufacture valve cover gaskets for:


Aircraft: Continental, Franklin, Lycoming, Pratt & Whitney and 

Wright radial piston aircraft engines.


Automobiles: Chevrolet, Ford, GM, Mopar, Porsche and VW 

automobile engines.  

Featuring NEW *ULTIMATE* GASKETS that are fiberglass 

reinforced silicone.          Check them out!


Motorcycles:  BMW, Harley-Davidson, Suzuki, BSA, Ducati, 

Moto Guzzi, Norton, Triumph, Saab and most other 

motorcycle engines.


If you are tired of oil leaks, then a silicone rubber gasket is the 

only way to go, and REAL Gaskets Tennessee is the only 

place you can get “The Original” silicone rubber gasket.


MADE IN THE USA.


CONTINENTAL Valve Cover Gasket -  FITS C-85, O-200 & more- # RG-530162 Silicone CONTINENTAL Valve Cover Gasket -  FITS C-85, O-200 & more- # RG-530162 Silicone CONTINENTAL Valve Cover Gasket -  FITS C-85, O-200 & more- # RG-530162 Silicone


Click here to purchase or contact the seller of this item on eBay